BMR series hydraulic motors are compact low-speed high-torque cycloid hydraulic motors, mainly used to convert pressure and flow in a hydraulic system into rotating mechanical power.
The basic hydraulic power path can be represented as:
Hydraulic pump → directional valve → BMR hydraulic motor → mechanical load
BMR motors mainly complete two energy conversions:
Hydraulic flow → rotational speed
And:
Pressure differential across the motor → output torque
The BMR series is widely used in:
Agricultural machinery
Forestry equipment
Machine tools
Plastic machinery
Sweeping equipment
Conveying equipment
Woodworking and sawmill equipment
And other industrial machinery requiring compact rotary power.
What Is a BMR Hydraulic Motor
BMR belongs to:
Cycloid hydraulic motors
Also commonly called:
Low-speed high-torque cycloid motors
Or:
Geroler-type hydraulic motors
Inside the BMR, a cycloid gear pair converts high-pressure hydraulic oil into output shaft rotation.
Compared with high-speed hydraulic motors, BMR emphasizes more:
Lower speed
And:
Higher output torque
Therefore, it is very suitable for equipment that requires:
Direct low-speed drive
Without the need to configure a complex large-ratio mechanical transmission.
Geroler Cycloid Roller Working Principle
Many BMR motors use:
Roller-type cycloid pair structure
The interior mainly includes:
Inner rotor
Outer gear ring
Rollers
When high-pressure hydraulic oil enters the motor, hydraulic force is formed inside the cycloid pair.
The hydraulic force pushes the inner rotor to produce:
Orbiting + rotation
Movement.
Then, through the internal transmission mechanism, this cycloid motion is converted into:
Output shaft rotation
The roller-type structure can reduce part of the sliding friction, helping to:
Improve mechanical efficiency
Reduce wear
Improve low-speed performance
Improve running smoothness
How the BMR Hydraulic Motor Works
The working process of the BMR can be simply divided into several stages.
- High-pressure oil enters the motor
The pressure oil output by the hydraulic pump enters one of the working ports.
- Hydraulic oil pushes the cycloid pair
Hydraulic force acts on the working chambers of the cycloid mechanism.
- The inner rotor produces cycloid motion
The rotor performs orbital motion around the center of the outer gear ring.
- The transmission mechanism outputs rotation
The internal transmission shaft converts the cycloid motion into output shaft rotation.
- Hydraulic oil returns to the system
After completing energy transmission, the hydraulic oil flows out from the other working port.
If the inlet and outlet directions of the two working ports are exchanged:
The motor rotation direction usually also reverses.
Low-Speed High-Torque Characteristics
One of the main advantages of the BMR series is:
Providing large torque at low speed
This makes it very suitable for:
Conveyors
Rollers
Winches
Rotary worktables
Feeding mechanisms
Agricultural machinery attachments
And other equipment requiring large direct driving force.
Compared with high-speed motors, BMR can reduce dependence on:
Large-ratio reduction mechanisms
BMR Motor Speed Is Mainly Determined by Flow
The speed of a hydraulic motor is mainly related to:
Hydraulic flow
And:
Motor displacement
Theoretically, it can be approximately expressed as:
Speed (rpm) ≈ flow (L/min) × 1000 ÷ displacement (mL/rev)
Therefore:
Flow increases → speed increases
And:
Displacement increases → speed decreases at the same flow
For example, at the same flow:
BMR-100
Usually rotates faster than:
BMR-200
Because BMR-200 requires more hydraulic oil per revolution.
Output Torque Mainly Depends on Pressure Differential
Hydraulic motor torque is mainly related to:
Motor displacement
And:
Pressure differential across the motor
It can be simply understood as:
The greater the pressure differential → the greater the output torque
When the mechanical load increases:
Required torque increases
↓
Pressure differential across the motor rises
But it must be noted:
The actual pressure differential must not exceed the motor’s allowable continuous, intermittent, and peak pressure ranges.
Common BMR Displacement Models
Common BMR models include:
BMR-50
BMR-80
BMR-100
BMR-125
BMR-160
BMR-200
BMR-250
BMR-315
BMR-400
The geometric displacements corresponding to some common series are approximately:
BMR-50 → approx. 51.7 mL/rev
BMR-80 → approx. 80.5 mL/rev
BMR-100 → approx. 100.5 mL/rev
BMR-125 → approx. 126.3 mL/rev
BMR-160 → approx. 160.8 mL/rev
BMR-200 → approx. 200.9 mL/rev
BMR-250 → approx. 252.6 mL/rev
BMR-315 → approx. 321.5 mL/rev
BMR-400 → approx. 401.9 mL/rev
Different manufacturers may also provide:
25
32
36
375
500 cm³/rev
And other specifications.
Therefore, during actual selection, the complete model and manufacturer parameters should be taken as the standard.
Why Displacement Is Very Important
Displacement affects both:
Speed
And:
Torque
At the same flow:
Smaller displacement → higher speed
Larger displacement → lower speed
At the same pressure differential:
Larger displacement → greater theoretical torque
Therefore:
A larger BMR displacement ≠ necessarily better
Correct selection requires comprehensive consideration of:
Target speed
Required torque
Hydraulic pump flow
System working pressure
BMR Pressure Capability
The allowable working pressure differential of BMR varies with:
Displacement
Structure
Brand
Among some common BMR series, for small and medium displacement models such as BMR-50 to BMR-200, the continuous working pressure differential may reach:
Approx. 14 MPa / 140 bar
The allowable continuous pressure differential of larger displacement models may decrease somewhat.
Intermittent and peak pressure differentials can usually be higher.
Therefore:
A single pressure value cannot represent all BMR models.
The specific model parameters should be confirmed when ordering.
Continuous, Intermittent, and Peak Working Conditions
Hydraulic motor catalogs usually distinguish:
Continuous working condition
Can operate for long periods.
Intermittent working condition
Allows higher load, but only for a limited time.
Peak working condition
Can only withstand maximum pressure or maximum torque for a short time.
Therefore, the BMR must not be operated for long periods under:
Peak pressure
Or:
Peak torque
Otherwise, motor life will be significantly shortened.
BMR Torque Range
BMR output torque is directly related to:
Displacement
And:
Pressure differential
For example, in some series:
BMR-50
The continuous maximum torque may be approximately:
Around 90 N·m class
And:
BMR-200
Continuous torque may reach:
More than 300 N·m
Larger displacement models can also provide higher torque.
The specific values must be confirmed according to:
The complete model performance curve
The Larger the Displacement, the Lower the Maximum Speed Usually
Small-displacement BMR motors can generally withstand higher speeds.
As displacement increases:
The maximum allowable speed usually decreases
For example, in some common series:
BMR-50 → maximum continuous speed can reach approx. 700 rpm or more
And:
BMR-400 → maximum continuous speed may be only approx. 150 rpm
Therefore, the following must be considered together:
Displacement + flow + speed
One parameter cannot be selected alone.
Common Maximum Flow
The maximum continuous flow of many BMR models is approximately in the range of:
40–60 L/min
Smaller displacement models may be approximately:
40 L/min
While some medium and large displacement models can reach:
Around 60 L/min
However:
Maximum flow
Does not equal:
The actual flow that the equipment should use for a long time
Actual selection should still be calculated according to the target speed.
Common SAE A Two-Bolt Mounting Flange
A very common mounting form of BMR is:
SAE A two-bolt flange
This structure is widely used in:
Agricultural machinery
Mobile hydraulic equipment
Industrial machinery
In addition to the two-bolt flange, some BMR motors may also provide:
Four-bolt square flange
Special flange
And other structures.
Therefore, when replacing, confirm:
Flange type
Mounting hole spacing
Centering spigot dimensions
Common 25.4 mm / 1 Inch Keyed Shaft
A very common output shaft configuration of BMR is:
Ø25.4 mm
That is:
1-inch keyed shaft
Some common configurations also use:
6.35 mm × 6.35 mm parallel key
This type of shaft is usually combined with:
SAE A two-bolt flange
For agricultural and industrial equipment replacement, this is one of the very common BMR configurations.
Other BMR Output Shaft Forms
Different manufacturers may also provide:
25 mm keyed shaft
32 mm keyed shaft
1-inch splined shaft
Multi-tooth splined shaft
Taper shaft
Larger diameter keyed shaft
Therefore, even if two motors are both marked:
BMR-160
The output shafts may not be the same.
The following must be confirmed:
Shaft diameter
Shaft length
Keyway
Spline
Shaft end form
BMR Port Forms
Common BMR working ports include:
BSPP thread
SAE thread
And other interface forms.
Some common configurations use:
1/2″ BSPP A/B working ports
In addition, there may also be:
Drain port
Or other special structures.
When replacing, confirm:
Thread standard
Port size
Port position
Drain method
Internal Drain and External Drain
Some BMR motors use:
Internal check drain structure
Internal leakage oil can achieve case pressure relief through the working ports.
In this case, it may be:
No independent drain line required
But other BMR versions may be equipped with:
Independent external drain port
Therefore:
It cannot be assumed that all BMR motors do not require a drain line.
It must be confirmed according to the specific model and port diagram.
BMR Rotation Direction
BMR can usually achieve:
Forward rotation
And:
Reverse rotation
By exchanging the inlet and outlet oil directions of the A/B ports.
For example:
A port inlet, B port return
The motor rotates in one direction.
After exchange:
B port inlet, A port return
The motor rotates in the opposite direction.
The actual clockwise or counterclockwise direction also needs to be combined with:
Observation direction
And:
Specific internal oil passages
For confirmation.
Difference Between BMR Hydraulic Motors and Hydraulic Pumps
Hydraulic pumps and hydraulic motors may have a certain similarity in appearance.
But their energy conversion directions are completely opposite.
Hydraulic pump
Mechanical energy → hydraulic flow and pressure
BMR hydraulic motor
Hydraulic pressure and flow → mechanical speed and torque
Therefore, BMR belongs to:
Rotary actuators
In the hydraulic system.
Difference Between BMR and BMM
BMM usually belongs to:
Smaller cycloid motors
Features include:
Smaller size
Lighter weight
Suitable for:
Low power
Smaller torque
Applications.
BMR usually has:
Higher torque
Higher flow capacity
Stronger output shaft structure
Therefore, even if the displacement numbers are similar, BMM cannot directly replace BMR.
Difference Between BMR and BMS / OMS-Type Motors
BMS or similar OMS-class cycloid motors are generally more oriented toward:
Heavy-duty applications
Compared with BMR, some BMS series may have:
Higher pressure
Greater torque
Stronger bearing structure
BMR is more suitable for:
Compact size
Medium flow
Low-speed high-torque
Conventional industrial and mobile hydraulic applications.
Difference Between BMR and A6V Piston Motors
BMR and A6V axial piston motors belong to completely different product structures.
BMR cycloid motor
Main features:
Low speed
High torque
Direct drive
Compact structure
A6V piston motor
More suitable for:
Higher pressure
Higher power density
Higher speed
Variable displacement control
Therefore, the two usually have different application scenarios.
Typical BMR Hydraulic Circuit
A simple BMR hydraulic motor circuit can be represented as:
Oil tank
↓
↓
↓
↓
↓
Oil tank
Among them:
Directional valve
Controls:
Start
Stop
And:
Rotation direction
Is responsible for limiting the maximum system pressure.
If speed adjustment is required, a:
Flow control valve
Can also be added.
How to Control BMR Speed
BMR speed can be controlled by changing:
Hydraulic flow
Typical circuit:
Hydraulic pump → flow control valve → BMR motor
If flow decreases:
Motor speed decreases
If flow increases:
Motor speed increases
But actual operation must not exceed:
Maximum allowable flow
Maximum allowable speed
At the same time, long-term operation below:
Minimum stable speed
Should also be avoided.
How to Control BMR Torque
BMR output torque is mainly determined by:
Pressure differential across the motor
If the mechanical load increases:
Required torque increases
↓
Motor working pressure differential rises
The:
In the system should be responsible for limiting the maximum pressure.
The relief setting must not exceed the allowable pressure of:
And other hydraulic components.
Starting Torque Is Very Important
Some equipment requires large torque at the moment of starting.
For example:
Fully loaded conveyors
Winches
Feed rollers
Agricultural machinery
Some motors may have sufficient torque during normal operation but may still have difficulty starting.
Common causes include:
Insufficient system pressure
Reduced motor efficiency
Mechanical load too large
Motor displacement too small
Therefore, when selecting, it is not enough to consider only:
Normal operating torque
Starting torque must also be considered.
Output Shaft Radial and Axial Loads
The BMR output shaft may be subjected to:
Radial load
For example:
Sprockets
Pulleys
Gears
It may also be subjected to:
Axial load
The specific allowable load depends on:
Output shaft form
Bearing structure
Force direction
Force position
Motor speed
Therefore, if the equipment directly installs a large sprocket or pulley on the motor shaft, it is not enough to check only:
Whether the torque is sufficient
The:
Bearing load capacity must also be confirmed.
Direct Drive and Chain Drive
BMR can be directly connected to mechanical equipment through:
A coupling
It can also be transmitted through:
Chains
Sprockets
Gears
Reduction gearboxes
If chains or belts are used:
Radial load on the output shaft increases
Therefore, the sprocket should preferably be as close as possible to:
The motor mounting flange
To reduce the bending moment on the shaft and bearing.
Typical Application: Agricultural Machinery
BMR is very commonly used in agricultural equipment.
It may be used for:
Seeding equipment
Feeding mechanisms
Conveyors
Rotary attachments
Fertilizing equipment
Harvesting machinery
Hydraulic motors can provide very flexible rotary power in positions where mechanical transmission is inconvenient.
Typical Application: Conveying Equipment
Conveying equipment usually requires:
Low speed
High starting torque
Reversible operation
BMR can directly drive:
Conveyor rollers
Chain conveyors
Material feeding mechanisms
By controlling hydraulic flow, the conveying speed can also be adjusted.
Typical Application: Machine Tools
In machine tools, BMR can be used for:
Rotary worktables
Feeding mechanisms
Positioning mechanisms
Auxiliary rotary drives
Hydraulic motors can achieve multiple rotary actions under a centralized hydraulic system.
Typical Application: Plastic and Injection Molding Equipment
BMR is also often used for auxiliary actions in plastic machinery and injection molding equipment.
For example:
Mold height adjustment
And other functions requiring:
Low speed
Stable rotation
Certain torque
Typical Application: Sweeping Equipment
BMR cycloid motors are also suitable for:
Sweeping brushes
Rotary cleaning equipment
Floor sweepers
These applications usually require:
Compact installation
Bi-directional rotation
Hydraulic speed regulation
Typical Application: Forestry and Sawmill Equipment
BMR can also be used for:
Sawmill worktables
Feed rollers
Wood conveying mechanisms
And other auxiliary drives of forestry machinery.
Such equipment usually requires:
Stable low speed
And:
Relatively large driving torque
Hydraulic Oil Cleanliness Is Very Important
Inside the BMR:
Cycloid pair
Oil distribution mechanism
Bearings
Output shaft
All depend on clean hydraulic oil for normal operation.
Contamination may cause:
Internal wear
Oil distribution surface damage
Bearing wear
Efficiency decrease
Increased internal leakage
Unstable speed
Therefore, a good filtration system is very important for BMR life.
Cavitation Must Be Avoided
If the motor oil supply is insufficient, cavitation may occur.
Typical symptoms include:
Abnormal noise
Vibration
Unstable speed
Internal surface damage
Especially under:
Rapid reversing
Or:
Overrunning load
Conditions, local oil starvation must be avoided even more.
Special Attention to Overrunning Loads
Some mechanical loads will push the hydraulic motor in reverse.
For example:
Lowering loads
High-inertia rotating equipment
Downhill conveyors
At this time, the BMR may act like:
A hydraulic pump
This working condition usually requires adding:
Counterbalance valves
Brake valves
Anti-cavitation check valves
And other control components.
The BMR motor alone cannot safely control overrunning loads.
Rapid Reversal May Generate Pressure Shock
If the directional valve switches directly from:
Forward rotation
Quickly to:
Reverse rotation
The motor and mechanical load will suddenly decelerate and reverse.
This may generate:
Pressure shock
Output shaft impact
Coupling stress
Hose pressure shock
If the equipment inertia is large, the following should be considered:
Decelerate first
Then:
Reverse
Common Fault: BMR Speed Too Slow
Possible causes include:
Insufficient hydraulic pump flow
Motor displacement too large
Motor internal leakage
Flow control valve restriction
Insufficient hydraulic pump speed
Hydraulic oil temperature too high
First compare:
Actual oil supply flow
With:
The target flow required for that displacement
Common Fault: Insufficient BMR Torque
Possible causes include:
Insufficient system pressure
Relief valve setting too low
Excessive motor internal leakage
Motor displacement too small
Mechanical load too large
Before replacing the motor, it is recommended to measure:
The actual pressure differential of the motor under load
Common Fault: Loud Motor Noise
Possible causes include:
Cavitation
Air in the hydraulic oil
Speed too high
Bearing wear
Installation misalignment
Incorrect hydraulic connection
When new abnormal noise appears, it should be checked as soon as possible.
Common Fault: Motor Heating
Possible causes include:
Excessive internal leakage
System pressure too high
Long-term operation near maximum load
Hydraulic oil temperature too high
Excessive return oil resistance
Motor specification too small
Overheating will reduce hydraulic oil viscosity and further increase internal leakage.
Common Fault: Output Shaft Seal Leakage
Possible causes include:
Excessive case pressure
Seal wear
Output shaft surface damage
Oil temperature too high
Incorrect drain configuration
If the BMR repeatedly damages the shaft seal, it is not enough to replace only the seal.
The following should also be checked:
System back pressure
And:
Drain conditions
Do Not Replace BMR Only by Displacement
Two hydraulic motors both marked:
May also be completely different.
Differences may include:
Flange
Output shaft
Port thread
Port position
Drain structure
Overall length
Bearing configuration
Therefore:
Same displacement ≠ direct replacement
The mechanical interface must be carefully confirmed.
Common Two-Bolt 25.4 mm Shaft Configuration
A very common BMR structure is:
SAE A two-bolt mounting
Ø25.4 mm / 1-inch keyed shaft
Some versions are also matched with:
1/2-inch BSPP working ports
This configuration is very common in:
Agricultural equipment
Conveying equipment
Industrial machinery
When replacing, it is recommended to confirm:
Center distance of the two mounting holes
Centering spigot diameter
Shaft diameter
Shaft length
Keyway dimensions
Port thread
BMR Replacement Selection Checklist
Before ordering, it is recommended to confirm:
- Complete original model
For example:
BMR-160
And all shaft, flange, and port suffixes.
- Displacement
mL/rev or cm³/rev.
- Target speed
Normal rpm.
- Required torque
Normal torque and starting torque.
- Working pressure
Continuous and maximum pressure differential.
- Flow
Normal flow and maximum flow.
- Mounting flange
Two-bolt, four-bolt, square, or other forms.
- Output shaft
25 mm, 25.4 mm, spline, taper shaft, etc.
- Port thread
BSPP, SAE, or other specifications.
- Drain
Internal drain or external drain.
- Rotation direction
Whether forward and reverse rotation is required.
- Equipment application
Conveyor, agricultural machinery, machine tool, etc.
What to Check Before Installation and Startup
Before installing a new BMR motor, check:
Whether the hydraulic hoses are clean
Whether the A/B working ports are confirmed
Whether the output shaft is aligned
Whether the flange dimensions match
Whether the coupling or sprocket is installed correctly
Whether the hydraulic oil is clean
Whether the relief valve pressure is correct
Whether air is removed from the system
If there is an external drain port, whether the drain line is connected correctly
For the first startup, it is recommended to:
Low load
Medium-low speed
Operation.
After confirming normal operation, gradually increase the load.
What Information to Provide When the Original Model Is Unclear
If the old motor nameplate can no longer be identified, provide:
Overall motor photos
Nameplate photo
Front mounting flange photo
Output shaft photo
Port photo
Mounting hole center distance
Centering spigot diameter
Output shaft diameter
Output shaft length
Keyway dimensions
Port thread
Equipment application
Target speed
Working pressure
This information helps determine a suitable replacement model.
How XYIYEYA Supports BMR Hydraulic Motor Replacement
XYIYEYA provides hydraulic motors, hydraulic pumps, and hydraulic valve products for industrial machinery, agricultural machinery, hydraulic power equipment, OEM, maintenance, and replacement projects.
Related motor products include:
BMR cycloid hydraulic motors
BMM cycloid motors
BMS and other heavy-duty cycloid motors
Fixed displacement hydraulic motors
Variable displacement hydraulic motors
If the customer needs a BMR hydraulic motor, they can provide:
Original model + displacement + pressure + flow + flange + output shaft + ports + product photos + equipment application
XYIYEYA can assist in confirming:
Hydraulic parameters
And:
Whether the mechanical installation dimensions match
Common configurations include:
Two-bolt mounting
And:
25.4 mm / 1-inch keyed shaft
Conclusion
BMR series cycloid hydraulic motors can provide compact low-speed high-torque rotary power for various industrial and mobile equipment.
Their main features include:
Cycloid / Geroler structure
Low-speed high-torque
Compact structure
Forward and reverse rotation
Multiple displacement specifications
Multiple output shafts and mounting flanges
Common models include:
Correct BMR selection cannot be based only on displacement.
The most important replacement parameters include:
Displacement + flow + pressure + speed + torque + flange + output shaft + ports
One of the more common mechanical configurations is:
SAE A two-bolt flange + Ø25.4 mm / 1-inch keyed shaft
But many other configurations also exist on the market.
With correct selection, correct installation, and the use of clean hydraulic oil, BMR hydraulic motors can provide reliable rotary power for:
Agricultural machinery
Conveying equipment
Industrial machinery
Automation equipment
Etc.
