News Center

Home » Industry News » BMR Series Low-Speed High-Torque Orbital Hydraulic Motors

BMR Series Low-Speed High-Torque Orbital Hydraulic Motors

BMR series hydraulic motors are compact low-speed high-torque cycloid hydraulic motors, mainly used to convert pressure and flow in a hydraulic system into rotating mechanical power.

The basic hydraulic power path can be represented as:

Hydraulic pump → directional valve → BMR hydraulic motor → mechanical load

BMR motors mainly complete two energy conversions:

Hydraulic flow → rotational speed

And:

Pressure differential across the motor → output torque

The BMR series is widely used in:

Agricultural machinery

Forestry equipment

Machine tools

Plastic machinery

Sweeping equipment

Conveying equipment

Woodworking and sawmill equipment

And other industrial machinery requiring compact rotary power.

What Is a BMR Hydraulic Motor

BMR belongs to:

Cycloid hydraulic motors

Also commonly called:

Low-speed high-torque cycloid motors

Or:

Geroler-type hydraulic motors

Inside the BMR, a cycloid gear pair converts high-pressure hydraulic oil into output shaft rotation.

Compared with high-speed hydraulic motors, BMR emphasizes more:

Lower speed

And:

Higher output torque

Therefore, it is very suitable for equipment that requires:

Direct low-speed drive

Without the need to configure a complex large-ratio mechanical transmission.

Geroler Cycloid Roller Working Principle

Many BMR motors use:

Roller-type cycloid pair structure

The interior mainly includes:

Inner rotor

Outer gear ring

Rollers

When high-pressure hydraulic oil enters the motor, hydraulic force is formed inside the cycloid pair.

The hydraulic force pushes the inner rotor to produce:

Orbiting + rotation

Movement.

Then, through the internal transmission mechanism, this cycloid motion is converted into:

Output shaft rotation

The roller-type structure can reduce part of the sliding friction, helping to:

Improve mechanical efficiency

Reduce wear

Improve low-speed performance

Improve running smoothness

How the BMR Hydraulic Motor Works

The working process of the BMR can be simply divided into several stages.

  1. High-pressure oil enters the motor

The pressure oil output by the hydraulic pump enters one of the working ports.

  1. Hydraulic oil pushes the cycloid pair

Hydraulic force acts on the working chambers of the cycloid mechanism.

  1. The inner rotor produces cycloid motion

The rotor performs orbital motion around the center of the outer gear ring.

  1. The transmission mechanism outputs rotation

The internal transmission shaft converts the cycloid motion into output shaft rotation.

  1. Hydraulic oil returns to the system

After completing energy transmission, the hydraulic oil flows out from the other working port.

If the inlet and outlet directions of the two working ports are exchanged:

The motor rotation direction usually also reverses.

Low-Speed High-Torque Characteristics

One of the main advantages of the BMR series is:

Providing large torque at low speed

This makes it very suitable for:

Conveyors

Rollers

Winches

Rotary worktables

Feeding mechanisms

Agricultural machinery attachments

And other equipment requiring large direct driving force.

Compared with high-speed motors, BMR can reduce dependence on:

Large-ratio reduction mechanisms

BMR Motor Speed Is Mainly Determined by Flow

The speed of a hydraulic motor is mainly related to:

Hydraulic flow

And:

Motor displacement

Theoretically, it can be approximately expressed as:

Speed (rpm) ≈ flow (L/min) × 1000 ÷ displacement (mL/rev)

Therefore:

Flow increases → speed increases

And:

Displacement increases → speed decreases at the same flow

For example, at the same flow:

BMR-100

Usually rotates faster than:

BMR-200

Because BMR-200 requires more hydraulic oil per revolution.

Output Torque Mainly Depends on Pressure Differential

Hydraulic motor torque is mainly related to:

Motor displacement

And:

Pressure differential across the motor

It can be simply understood as:

The greater the pressure differential → the greater the output torque

When the mechanical load increases:

Required torque increases

↓

Pressure differential across the motor rises

But it must be noted:

The actual pressure differential must not exceed the motor’s allowable continuous, intermittent, and peak pressure ranges.

Common BMR Displacement Models

Common BMR models include:

BMR-50

BMR-80

BMR-100

BMR-125

BMR-160

BMR-200

BMR-250

BMR-315

BMR-400

The geometric displacements corresponding to some common series are approximately:

BMR-50 → approx. 51.7 mL/rev

BMR-80 → approx. 80.5 mL/rev

BMR-100 → approx. 100.5 mL/rev

BMR-125 → approx. 126.3 mL/rev

BMR-160 → approx. 160.8 mL/rev

BMR-200 → approx. 200.9 mL/rev

BMR-250 → approx. 252.6 mL/rev

BMR-315 → approx. 321.5 mL/rev

BMR-400 → approx. 401.9 mL/rev

Different manufacturers may also provide:

25

32

36

375

500 cm³/rev

And other specifications.

Therefore, during actual selection, the complete model and manufacturer parameters should be taken as the standard.

Why Displacement Is Very Important

Displacement affects both:

Speed

And:

Torque

At the same flow:

Smaller displacement → higher speed

Larger displacement → lower speed

At the same pressure differential:

Larger displacement → greater theoretical torque

Therefore:

A larger BMR displacement ≠ necessarily better

Correct selection requires comprehensive consideration of:

Target speed

Required torque

Hydraulic pump flow

System working pressure

BMR Pressure Capability

The allowable working pressure differential of BMR varies with:

Displacement

Structure

Brand

Among some common BMR series, for small and medium displacement models such as BMR-50 to BMR-200, the continuous working pressure differential may reach:

Approx. 14 MPa / 140 bar

The allowable continuous pressure differential of larger displacement models may decrease somewhat.

Intermittent and peak pressure differentials can usually be higher.

Therefore:

A single pressure value cannot represent all BMR models.

The specific model parameters should be confirmed when ordering.

Continuous, Intermittent, and Peak Working Conditions

Hydraulic motor catalogs usually distinguish:

Continuous working condition

Can operate for long periods.

Intermittent working condition

Allows higher load, but only for a limited time.

Peak working condition

Can only withstand maximum pressure or maximum torque for a short time.

Therefore, the BMR must not be operated for long periods under:

Peak pressure

Or:

Peak torque

Otherwise, motor life will be significantly shortened.

BMR Torque Range

BMR output torque is directly related to:

Displacement

And:

Pressure differential

For example, in some series:

BMR-50

The continuous maximum torque may be approximately:

Around 90 N·m class

And:

BMR-200

Continuous torque may reach:

More than 300 N·m

Larger displacement models can also provide higher torque.

The specific values must be confirmed according to:

The complete model performance curve

The Larger the Displacement, the Lower the Maximum Speed Usually

Small-displacement BMR motors can generally withstand higher speeds.

As displacement increases:

The maximum allowable speed usually decreases

For example, in some common series:

BMR-50 → maximum continuous speed can reach approx. 700 rpm or more

And:

BMR-400 → maximum continuous speed may be only approx. 150 rpm

Therefore, the following must be considered together:

Displacement + flow + speed

One parameter cannot be selected alone.

Common Maximum Flow

The maximum continuous flow of many BMR models is approximately in the range of:

40–60 L/min

Smaller displacement models may be approximately:

40 L/min

While some medium and large displacement models can reach:

Around 60 L/min

However:

Maximum flow

Does not equal:

The actual flow that the equipment should use for a long time

Actual selection should still be calculated according to the target speed.

Common SAE A Two-Bolt Mounting Flange

A very common mounting form of BMR is:

SAE A two-bolt flange

This structure is widely used in:

Agricultural machinery

Mobile hydraulic equipment

Industrial machinery

In addition to the two-bolt flange, some BMR motors may also provide:

Four-bolt square flange

Special flange

And other structures.

Therefore, when replacing, confirm:

Flange type

Mounting hole spacing

Centering spigot dimensions

Common 25.4 mm / 1 Inch Keyed Shaft

A very common output shaft configuration of BMR is:

Ø25.4 mm

That is:

1-inch keyed shaft

Some common configurations also use:

6.35 mm × 6.35 mm parallel key

This type of shaft is usually combined with:

SAE A two-bolt flange

For agricultural and industrial equipment replacement, this is one of the very common BMR configurations.

Other BMR Output Shaft Forms

Different manufacturers may also provide:

25 mm keyed shaft

32 mm keyed shaft

1-inch splined shaft

Multi-tooth splined shaft

Taper shaft

Larger diameter keyed shaft

Therefore, even if two motors are both marked:

BMR-160

The output shafts may not be the same.

The following must be confirmed:

Shaft diameter

Shaft length

Keyway

Spline

Shaft end form

BMR Port Forms

Common BMR working ports include:

BSPP thread

SAE thread

And other interface forms.

Some common configurations use:

1/2″ BSPP A/B working ports

In addition, there may also be:

Drain port

Or other special structures.

When replacing, confirm:

Thread standard

Port size

Port position

Drain method

Internal Drain and External Drain

Some BMR motors use:

Internal check drain structure

Internal leakage oil can achieve case pressure relief through the working ports.

In this case, it may be:

No independent drain line required

But other BMR versions may be equipped with:

Independent external drain port

Therefore:

It cannot be assumed that all BMR motors do not require a drain line.

It must be confirmed according to the specific model and port diagram.

BMR Rotation Direction

BMR can usually achieve:

Forward rotation

And:

Reverse rotation

By exchanging the inlet and outlet oil directions of the A/B ports.

For example:

A port inlet, B port return

The motor rotates in one direction.

After exchange:

B port inlet, A port return

The motor rotates in the opposite direction.

The actual clockwise or counterclockwise direction also needs to be combined with:

Observation direction

And:

Specific internal oil passages

For confirmation.

Difference Between BMR Hydraulic Motors and Hydraulic Pumps

Hydraulic pumps and hydraulic motors may have a certain similarity in appearance.

But their energy conversion directions are completely opposite.

Hydraulic pump

Mechanical energy → hydraulic flow and pressure

BMR hydraulic motor

Hydraulic pressure and flow → mechanical speed and torque

Therefore, BMR belongs to:

Rotary actuators

In the hydraulic system.

Difference Between BMR and BMM

BMM usually belongs to:

Smaller cycloid motors

Features include:

Smaller size

Lighter weight

Suitable for:

Low power

Smaller torque

Applications.

BMR usually has:

Higher torque

Higher flow capacity

Stronger output shaft structure

Therefore, even if the displacement numbers are similar, BMM cannot directly replace BMR.

Difference Between BMR and BMS / OMS-Type Motors

BMS or similar OMS-class cycloid motors are generally more oriented toward:

Heavy-duty applications

Compared with BMR, some BMS series may have:

Higher pressure

Greater torque

Stronger bearing structure

BMR is more suitable for:

Compact size

Medium flow

Low-speed high-torque

Conventional industrial and mobile hydraulic applications.

Difference Between BMR and A6V Piston Motors

BMR and A6V axial piston motors belong to completely different product structures.

BMR cycloid motor

Main features:

Low speed

High torque

Direct drive

Compact structure

A6V piston motor

More suitable for:

Higher pressure

Higher power density

Higher speed

Variable displacement control

Therefore, the two usually have different application scenarios.

Typical BMR Hydraulic Circuit

A simple BMR hydraulic motor circuit can be represented as:

Oil tank

↓

Hydraulic pump

↓

Relief valve

↓

Directional valve

↓

BMR hydraulic motor

↓

Oil tank

Among them:

Directional valve

Controls:

Start

Stop

And:

Rotation direction

Relief valve

Is responsible for limiting the maximum system pressure.

If speed adjustment is required, a:

Flow control valve

Can also be added.

How to Control BMR Speed

BMR speed can be controlled by changing:

Hydraulic flow

Typical circuit:

Hydraulic pump → flow control valve → BMR motor

If flow decreases:

Motor speed decreases

If flow increases:

Motor speed increases

But actual operation must not exceed:

Maximum allowable flow

Maximum allowable speed

At the same time, long-term operation below:

Minimum stable speed

Should also be avoided.

How to Control BMR Torque

BMR output torque is mainly determined by:

Pressure differential across the motor

If the mechanical load increases:

Required torque increases

↓

Motor working pressure differential rises

The:

Relief valve

In the system should be responsible for limiting the maximum pressure.

The relief setting must not exceed the allowable pressure of:

The motor

Hoses

Directional valve

And other hydraulic components.

Starting Torque Is Very Important

Some equipment requires large torque at the moment of starting.

For example:

Fully loaded conveyors

Winches

Feed rollers

Agricultural machinery

Some motors may have sufficient torque during normal operation but may still have difficulty starting.

Common causes include:

Insufficient system pressure

Reduced motor efficiency

Mechanical load too large

Motor displacement too small

Therefore, when selecting, it is not enough to consider only:

Normal operating torque

Starting torque must also be considered.

Output Shaft Radial and Axial Loads

The BMR output shaft may be subjected to:

Radial load

For example:

Sprockets

Pulleys

Gears

It may also be subjected to:

Axial load

The specific allowable load depends on:

Output shaft form

Bearing structure

Force direction

Force position

Motor speed

Therefore, if the equipment directly installs a large sprocket or pulley on the motor shaft, it is not enough to check only:

Whether the torque is sufficient

The:

Bearing load capacity must also be confirmed.

Direct Drive and Chain Drive

BMR can be directly connected to mechanical equipment through:

A coupling

It can also be transmitted through:

Chains

Sprockets

Gears

Reduction gearboxes

If chains or belts are used:

Radial load on the output shaft increases

Therefore, the sprocket should preferably be as close as possible to:

The motor mounting flange

To reduce the bending moment on the shaft and bearing.

Typical Application: Agricultural Machinery

BMR is very commonly used in agricultural equipment.

It may be used for:

Seeding equipment

Feeding mechanisms

Conveyors

Rotary attachments

Fertilizing equipment

Harvesting machinery

Hydraulic motors can provide very flexible rotary power in positions where mechanical transmission is inconvenient.

Typical Application: Conveying Equipment

Conveying equipment usually requires:

Low speed

High starting torque

Reversible operation

BMR can directly drive:

Conveyor rollers

Chain conveyors

Material feeding mechanisms

By controlling hydraulic flow, the conveying speed can also be adjusted.

Typical Application: Machine Tools

In machine tools, BMR can be used for:

Rotary worktables

Feeding mechanisms

Positioning mechanisms

Auxiliary rotary drives

Hydraulic motors can achieve multiple rotary actions under a centralized hydraulic system.

Typical Application: Plastic and Injection Molding Equipment

BMR is also often used for auxiliary actions in plastic machinery and injection molding equipment.

For example:

Mold height adjustment

And other functions requiring:

Low speed

Stable rotation

Certain torque

Typical Application: Sweeping Equipment

BMR cycloid motors are also suitable for:

Sweeping brushes

Rotary cleaning equipment

Floor sweepers

These applications usually require:

Compact installation

Bi-directional rotation

Hydraulic speed regulation

Typical Application: Forestry and Sawmill Equipment

BMR can also be used for:

Sawmill worktables

Feed rollers

Wood conveying mechanisms

And other auxiliary drives of forestry machinery.

Such equipment usually requires:

Stable low speed

And:

Relatively large driving torque

Hydraulic Oil Cleanliness Is Very Important

Inside the BMR:

Cycloid pair

Oil distribution mechanism

Bearings

Output shaft

All depend on clean hydraulic oil for normal operation.

Contamination may cause:

Internal wear

Oil distribution surface damage

Bearing wear

Efficiency decrease

Increased internal leakage

Unstable speed

Therefore, a good filtration system is very important for BMR life.

Cavitation Must Be Avoided

If the motor oil supply is insufficient, cavitation may occur.

Typical symptoms include:

Abnormal noise

Vibration

Unstable speed

Internal surface damage

Especially under:

Rapid reversing

Or:

Overrunning load

Conditions, local oil starvation must be avoided even more.

Special Attention to Overrunning Loads

Some mechanical loads will push the hydraulic motor in reverse.

For example:

Lowering loads

High-inertia rotating equipment

Downhill conveyors

At this time, the BMR may act like:

A hydraulic pump

This working condition usually requires adding:

Counterbalance valves

Brake valves

Anti-cavitation check valves

And other control components.

The BMR motor alone cannot safely control overrunning loads.

Rapid Reversal May Generate Pressure Shock

If the directional valve switches directly from:

Forward rotation

Quickly to:

Reverse rotation

The motor and mechanical load will suddenly decelerate and reverse.

This may generate:

Pressure shock

Output shaft impact

Coupling stress

Hose pressure shock

If the equipment inertia is large, the following should be considered:

Decelerate first

Then:

Reverse

Common Fault: BMR Speed Too Slow

Possible causes include:

Insufficient hydraulic pump flow

Motor displacement too large

Motor internal leakage

Flow control valve restriction

Insufficient hydraulic pump speed

Hydraulic oil temperature too high

First compare:

Actual oil supply flow

With:

The target flow required for that displacement

Common Fault: Insufficient BMR Torque

Possible causes include:

Insufficient system pressure

Relief valve setting too low

Excessive motor internal leakage

Motor displacement too small

Mechanical load too large

Before replacing the motor, it is recommended to measure:

The actual pressure differential of the motor under load

Common Fault: Loud Motor Noise

Possible causes include:

Cavitation

Air in the hydraulic oil

Speed too high

Bearing wear

Installation misalignment

Incorrect hydraulic connection

When new abnormal noise appears, it should be checked as soon as possible.

Common Fault: Motor Heating

Possible causes include:

Excessive internal leakage

System pressure too high

Long-term operation near maximum load

Hydraulic oil temperature too high

Excessive return oil resistance

Motor specification too small

Overheating will reduce hydraulic oil viscosity and further increase internal leakage.

Common Fault: Output Shaft Seal Leakage

Possible causes include:

Excessive case pressure

Seal wear

Output shaft surface damage

Oil temperature too high

Incorrect drain configuration

If the BMR repeatedly damages the shaft seal, it is not enough to replace only the seal.

The following should also be checked:

System back pressure

And:

Drain conditions

Do Not Replace BMR Only by Displacement

Two hydraulic motors both marked:

BMR-160

May also be completely different.

Differences may include:

Flange

Output shaft

Port thread

Port position

Drain structure

Overall length

Bearing configuration

Therefore:

Same displacement ≠ direct replacement

The mechanical interface must be carefully confirmed.

Common Two-Bolt 25.4 mm Shaft Configuration

A very common BMR structure is:

SAE A two-bolt mounting

Ø25.4 mm / 1-inch keyed shaft

Some versions are also matched with:

1/2-inch BSPP working ports

This configuration is very common in:

Agricultural equipment

Conveying equipment

Industrial machinery

When replacing, it is recommended to confirm:

Center distance of the two mounting holes

Centering spigot diameter

Shaft diameter

Shaft length

Keyway dimensions

Port thread

BMR Replacement Selection Checklist

Before ordering, it is recommended to confirm:

  1. Complete original model

For example:

BMR-160

And all shaft, flange, and port suffixes.

  1. Displacement

mL/rev or cm³/rev.

  1. Target speed

Normal rpm.

  1. Required torque

Normal torque and starting torque.

  1. Working pressure

Continuous and maximum pressure differential.

  1. Flow

Normal flow and maximum flow.

  1. Mounting flange

Two-bolt, four-bolt, square, or other forms.

  1. Output shaft

25 mm, 25.4 mm, spline, taper shaft, etc.

  1. Port thread

BSPP, SAE, or other specifications.

  1. Drain

Internal drain or external drain.

  1. Rotation direction

Whether forward and reverse rotation is required.

  1. Equipment application

Conveyor, agricultural machinery, machine tool, etc.

What to Check Before Installation and Startup

Before installing a new BMR motor, check:

Whether the hydraulic hoses are clean

Whether the A/B working ports are confirmed

Whether the output shaft is aligned

Whether the flange dimensions match

Whether the coupling or sprocket is installed correctly

Whether the hydraulic oil is clean

Whether the relief valve pressure is correct

Whether air is removed from the system

If there is an external drain port, whether the drain line is connected correctly

For the first startup, it is recommended to:

Low load

Medium-low speed

Operation.

After confirming normal operation, gradually increase the load.

What Information to Provide When the Original Model Is Unclear

If the old motor nameplate can no longer be identified, provide:

Overall motor photos

Nameplate photo

Front mounting flange photo

Output shaft photo

Port photo

Mounting hole center distance

Centering spigot diameter

Output shaft diameter

Output shaft length

Keyway dimensions

Port thread

Equipment application

Target speed

Working pressure

This information helps determine a suitable replacement model.

How XYIYEYA Supports BMR Hydraulic Motor Replacement

XYIYEYA provides hydraulic motors, hydraulic pumps, and hydraulic valve products for industrial machinery, agricultural machinery, hydraulic power equipment, OEM, maintenance, and replacement projects.

Related motor products include:

BMR cycloid hydraulic motors

BMM cycloid motors

BMS and other heavy-duty cycloid motors

Fixed displacement hydraulic motors

Variable displacement hydraulic motors

If the customer needs a BMR hydraulic motor, they can provide:

Original model + displacement + pressure + flow + flange + output shaft + ports + product photos + equipment application

XYIYEYA can assist in confirming:

Hydraulic parameters

And:

Whether the mechanical installation dimensions match

Common configurations include:

Two-bolt mounting

And:

25.4 mm / 1-inch keyed shaft

Conclusion

BMR series cycloid hydraulic motors can provide compact low-speed high-torque rotary power for various industrial and mobile equipment.

Their main features include:

Cycloid / Geroler structure

Low-speed high-torque

Compact structure

Forward and reverse rotation

Multiple displacement specifications

Multiple output shafts and mounting flanges

Common models include:

BMR-50

BMR-80

BMR-100

BMR-125

BMR-160

BMR-200

BMR-250

BMR-315

BMR-400

Correct BMR selection cannot be based only on displacement.

The most important replacement parameters include:

Displacement + flow + pressure + speed + torque + flange + output shaft + ports

One of the more common mechanical configurations is:

SAE A two-bolt flange + Ø25.4 mm / 1-inch keyed shaft

But many other configurations also exist on the market.

With correct selection, correct installation, and the use of clean hydraulic oil, BMR hydraulic motors can provide reliable rotary power for:

Agricultural machinery

Conveying equipment

Industrial machinery

Automation equipment

Etc.

滚动至顶部